Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateTrusted Garage Door Repair for Burbank Homeowners
When a garage door stops working in Burbank, it’s rarely a small inconvenience. It blocks your car, exposes your home, and grinds your morning to a halt. We’re Anchor Garage Door Repair, led by Noel Carranza, and we fix doors and openers across Burbank same-day in most cases. Homeowners call us when a spring snaps in the Verdugo foothills heat, when a sensor misaligns after a bump, or when a door that worked yesterday refuses to open today. We show up with a truck stocked for the common failures and a technician who services LiftMaster, Genie, Raynor, Chamberlain, Clopay, Amarr, Wayne Dalton, and Craftsman. One call covers the repair. Call (833) 589-9142 and we’ll quote the work before it starts.
Garage Door Spring Repair
Garage Door Spring Repair in Burbank typically runs between $180 and $340, and it’s the single most common service call we make. The torsion springs above your door bear the full weight every time it opens. When one snaps, your door becomes a dead weight: it won’t lift without a fight, and sometimes not at all. In this climate, the dry heat and temperature swings between the valley floor and the hills put real stress on spring steel. Anchor Garage Door Repair, as detailed in The Complete Garage Door Repair Guide for Burbank Homeowners, replaces both springs as a set, because when one breaks, the other is usually within months of the same failure. We carry torsion and extension springs to match your door’s exact weight and cycle rating.
Matching the Right Spring
The wrong spring rating won’t last. We measure wire gauge, coil diameter, and door weight before recommending a spring. Production doors, custom wood doors, and high-cycle doors each need different hardware.
When to Replace vs. Repair
Springs rarely repair safely. A broken or stretched spring gets replaced, not patched. We quote the replacement price upfront, typically $180 to $340 for both springs, so there’s no guesswork.
Safety first: garage door springs are under extreme tension and can cause serious injury if handled incorrectly. Do not attempt to remove or adjust them yourself. Call a trained technician.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Sensor Repair
Garage Door Sensor Repair addresses the photo-eye sensors near the bottom of each track that prevent the door from closing on a person, car, or pet. When a sensor’s alignment drifts, the door reverses for no visible reason. In Burbank garages, we see sensors bump out of alignment from bikes, trash cans, and parked SUVs. Sometimes the wiring gets chewed, or the lens is so dusty the beam breaks. Anchor Garage Door Repair checks both sensors, cleans the lenses, realigns the beam, and verifies the wiring before assuming the sensor needs replacement. If replacement is needed, the cost falls into our $150 to $600 repair range, with most sensor jobs landing on the low end.
Alignment vs. Replacement
Nine out of ten sensor calls are alignment or wiring problems, not dead sensors. We test the beam with a level and chase the wiring back to the opener before quoting a replacement.
When the Door Reverses on Its Own
A door that reverses with nothing in the way is almost always a sensor issue. We check the direct sunlight angle too: early morning glare off a neighbor’s window can blind a photo-eye. Relocation or a small hood often solves it.
Emergency Garage Door Repair
Emergency Garage Door Repair is what you need when the door won’t close at night, when the car is trapped inside, or when a spring fails during a holiday weekend. In Burbank, a broken door is also a security problem: an open bay is an invitation, especially near busy corridors. Anchor Garage Door Repair answers calls for urgent repairs and dispatches to Burbank as quickly as possible. We keep common springs, cables, and rollers on the truck, so many emergency visits wrap up in one trip. Emergency repair work falls within our standard repair range of $150 to $600, and your price is fixed before the work begins.
Securing the Home First
Our first job on an emergency call is making your home secure, even if that means bracing the door so it stays closed until parts arrive. We don’t leave a door hanging open when a fix can’t be completed the same day.
What Gets Fixed Today
Broken springs, snapped cables, and bent tracks are the most common emergencies. Most are repairable on the spot. We carry a range of torsion springs and cable assemblies sized for residential doors, which keeps one-trip fixes common.
Garage Door Panel Replacement
Garage Door Panel Replacement is the fix for a dented, cracked, or warped door section that ruins the look of your Burbank home from the street. A single panel damaged by a car tap or a basketball can make the whole door look worn. Depending on the door model, we can often replace individual panels rather than the entire door, which keeps the job between $250 and $500 per panel. Anchor Garage Door Repair matches the panel’s manufacturer, material, and color as closely as the door’s age allows. If your door is older, we’ll tell you honestly whether a single panel will match or whether the full door should be considered.
Matching an Existing Door
Weather fades every panel over time. A brand-new panel on a seven-year-old door will show. We use the manufacturer’s color codes and will tell you upfront if a match won’t be perfect.
Single Panel vs. Full Door
Structural damage to more than one panel usually signals a bigger problem. If the stiles are broken or the door is sagging, we’ll walk you through replacement cost for the entire door so you can compare instead of guessing.
Garage Door Maintenance
Garage Door Maintenance in Burbank keeps a functioning door from surprise failures. The dry heat and fine dust here work their way into hinges, rollers, and opener gears. A door that gets ignored will eventually fail; a door that gets serviced once a year, following a Garage Door Repair Maintenance Checklist for Burbank Homeowners, will typically outlast its expected service life. Anchor Garage Door Repair performs a full-point check: spring tension, cable condition, roller wear, track alignment, hinge tightness, sensor function, and opener force settings. Maintenance visits fall within our general repair $150 to $600 range depending on what we find and what small parts need replacing, and you’ll get the price before we turn a wrench.
What a Tune-Up Covers
We check the spring balance by disconnecting the opener and lifting the door manually. We test reversal pressure on the opener, tighten every hinge and bracket, and lubricate moving parts with the right grease, not a spray-all shortcut.
Why Annual Service Pays Off
A $120 roller replacement caught during a maintenance visit prevents a $300 spring failure and a down door. That’s the whole math. Most doors we maintain go years between actual breakdowns.
Garage Door Roller Replacement
Garage Door Roller Replacement swaps out worn metal or nylon rollers for new ones, typically costing $110 to $220 for a full set. Rollers are the wheels that carry your door along the tracks. When they flatten, seize, or start grinding, the door shakes, squeals, and puts extra load on the springs and opener. In Burbank, where garage doors cycle multiple times a day for commuters, roller wear shows up early. Anchor Garage Door Repair checks all rollers during every service call, and we’ll replace them when they show flat spots or wobble rather than waiting for one to snap.
Nylon vs. Steel Rollers
Nylon rollers run quieter and don’t tear up tracks like worn steel can. We stock both and recommend based on your door’s weight. Most residential doors do fine with quality nylon rollers, which is why they’re our standard.
When Rollers Fail
A roller that comes off its track can wedge the door against the frame. If you hear grinding or see the door wobbling as it moves, stop using it and give us a call. Forcing a door with a seized roller bends hardware and turns a $150 job into a $500 one.
Commercial Garage Door Repair
Commercial Garage Door Repair serves Burbank warehouses, storage facilities, maintenance yards, and retail loading docks that rely on doors that cycle hundreds of times a week. Commercial doors are heavier, use larger springs, and fail more suddenly when neglected. Anchor Garage Door Repair handles commercial door repairs across the repair range of $150 to $600 for typical fixes, and we will always quote the job before starting. We work on rolling steel doors, section overhead doors, and commercial operators. If your business is losing access because a door is down, call us directly and we’ll get someone on it.
High-Cycle Hardware Matters
Commercial doors need high-cycle springs and heavy-duty openers. We don’t just replace what’s broken, we check whether the door’s cycle rating matches the way your business actually uses it. A door that runs 300 cycles a day shouldn’t have 10,000-cycle springs.
Minimizing Downtime
Most commercial repair calls get completed in one visit. We carry a range of commercial springs, cables, and rollers, and when a section needs replacement we order it and secure the door in the meantime. Your loading dock won’t sit unusable while we wait for parts.
Garage Door Cable Repair
Garage Door Cable Repair fixes the steel cables that work with your springs to lift and lower the door safely. When a cable frays or snaps, one side of the door drops, and continuing to operate it is dangerous: a cable that breaks under tension can whip, and a door with one good cable can jump its track. Repair typically runs $130 to $250. In Burbank we see cable failures on aging doors where the cable rubs against a worn pulley or where rust has set in from garage moisture. Anchor Garage Door Repair replaces both cables as a set and checks the drums and pulleys at the same time, because a fresh cable on a bad pulley will fray again.
Why Cables Fail Together
Cables are a matched pair. One never fails without the other being stretched or damaged. We replace both so the door lifts evenly. It’s the same reason we do both springs.
Signs a Cable Is About to Go
You’ll see visible fraying, the door will hang slightly unevenly, and you may hear a popping sound under load. If any of this shows up, stop the door and call. A snapped cable is a quick fix; a door off its track from operating with a broken cable is not.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
The brands in Burbank garages run the full range. We service LiftMaster openers more than any other brand in the valley, and we stock their logic boards and safety sensors on the truck. Chamberlain and Genie are nearly as common, and we’ve repaired enough of each to recognize their typical failures by sound. On the door side, Raynor, Clopay, Amarr, and Wayne Dalton all pass through our service schedule regularly. Each has different panel profiles, spring ratings, and hardware, and we work with the right parts for the door you own, not a generic substitute.
Our techs diagnose by symptom first: how the door sounds, how it moves, where it stops. That approach works whether you have a LiftMaster opener on a Clopay door or a Genie on an Amarr. If you’re not sure what brand you have, that’s fine. We’ll identify it on arrival and go from there. Whether it’s Raynor, LiftMaster, Chamberlain, Genie, or another make altogether, we can help.
Signs You Need a Pro Right Now
- A loud snap or bang from the garage. That’s a spring breaking under tension. The door becomes extremely heavy and dangerous to lift by hand. Stop using it immediately and call us.
- The door opens a few inches and stops. This usually means a broken spring or a serious cable problem. Forcing it with the opener will burn out the motor and could pull the door off its track.
- One side of the door hangs lower than the other. Cables or springs are failing on one side. Continuing to cycle it will worsen the damage, especially if a cable lets go entirely.
- The door reverses without anything in the way. Sensor misalignment or a failing opener logic board. This one is often a quick fix, but it makes the door unusable until it’s addressed.
- Visible fraying on the cables. Cables don’t give much warning. If you can see broken strands or a loose cable on the drum, don’t run the door. Have a professional release the tension safely.
Our Process, Step by Step
- 1
You call and describe the problem. You’ll reach us directly at (833) 589-9142. We’ll ask what the door is doing, what brand it is if you know, and when it started. That gives us a head start on parts.
- 2
We arrive and diagnose. Your technician does a full inspection, not just a glance at what’s broken. We check the springs, cables, rollers, tracks, opener, and sensors so nothing remains hiding behind the immediate failure.
- 3
We quote before we work. You’ll get a fixed price for the repair or replacement before any work starts. No open-ended labor, no surprise line items. You approve it first.
- 4
We fix it right. We carry replacement parts from all major brands on the truck and use OEM or manufacturer-equivalent hardware. Most repairs finish in one visit.
- 5
We test and walk through. Before we leave, we cycle the door several times, test the safety reversal, and run through what we replaced and why. Then we show you how to keep it running well.
How Much Does Garage Door Repair Cost in Burbank?
Most Garage Door Repair pricing in Burbank falls between $150 and $600. A typical spring replacement runs $180 to $340 for the pair. Cable replacement sits between $130 and $250. Roller replacement runs $110 to $220, and panel replacement lands between $250 and $500 per panel. If your opener needs repair rather than the door itself, plan on $120 to $320. New opener installation runs $250 to $550, and a complete new door starts at $700 and can reach $2,200 depending on size, material, and insulation.
What affects the price: the door’s weight and spring system, whether you have a standard or custom door, the opener’s age, and whether parts are in stock locally. You’ll pay less for a standard 7-foot residential door than for a custom-height or wood door. The best way to avoid overpaying is to work with someone who quotes the job before starting and who carries parts on the truck rather than ordering everything per call. Anchor Garage Door Repair gives free estimates with no obligation, and you’ll always know the price before we start work.
Our Service Area Near Burbank
In addition to Burbank, we serve North Hollywood, Van Nuys, and the nearby communities of Hollywood, Studio City, Sherman Oaks, Glendale, Valley Village, West Hollywood, and Tarzana. If you’re just outside these areas, give us a call and we’ll tell you whether we can get to you. We keep our service radius close so response times stay short and our technicians know the neighborhoods they work in.
Serving Burbank, CA – Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Repair in Burbank
Garage door repair is the process of diagnosing and fixing any part of your garage door system that’s broken, worn, or out of adjustment. It covers springs, cables, rollers, tracks, hinges, sensors, panels, and openers. In Burbank, where doors cycle daily for commuters, most Burbank Garage Door Repair calls are for springs and openers. Anchor Garage Door Repair handles all of it, from a clicking opener to a door that won’t lift.
Most repairs finish in one to two hours from the time we arrive. Spring replacement, cable replacement, and sensor alignment are all standard one-visit jobs. Panel replacement can take longer if we need to order a matching section. We’ll give you a realistic timeframe when we diagnose the door, and we’ll keep you updated on anything that changes. Call (833) 589-9142 to schedule.
Garage door repair in Burbank typically runs $150 to $600, with specific jobs like spring repair at $180 to $340 and cable repair at $130 to $250. The cost depends on which part failed and what your door needs replaced. You’ll always get a fixed quote before work begins, so the final price matches the number you approved. Estimates are free.
Yes. We service LiftMaster, Genie, Chamberlain, Raynor, and most other major opener and door brands. Our technicians work on the opener’s mechanics and logic, not just the door hardware. Whether your opener is clicking, reversing, or dead, we can diagnose it and repair or replace it. We carry common LiftMaster and Genie parts on the truck to keep visits to one trip.
We make every effort to reach Burbank emergency calls the same day, especially when a door is stuck open or the car is trapped inside. Call (833) 589-9142 and tell us what happened. We’ll dispatch the nearest technician and let you know the estimated arrival window. If we can’t complete the repair immediately, we’ll secure the door so your home isn’t exposed.
Yes, our repairs are backed by a workmanship warranty, and the parts we install carry their manufacturer’s warranty. Specific warranty terms depend on the part and the repair. We’ll explain exactly what’s covered before we start, so you don’t have to wonder later. If something isn’t right after we leave, call us and we’ll make it right.
Clear the area in front of and inside the garage door so we have room to work and access the springs, tracks, and opener. Move vehicles out of the garage if possible. If you know the brand of your door and opener, have that handy, but it’s not required. We’ll handle the rest. Our home page has more details on what to expect during service.
Schedule Your Garage Door Repair Service in Burbank Today
When your garage door won’t wait, call Anchor Garage Door Repair at (833) 589-9142 and get a free estimate. We’ll send a technician to your Burbank home, diagnose the problem, and give you the price before we start. No obligation, no sales pitch, just a door that works again.
Written by Noel Carranza, Owner at Anchor Garage Door Repair, serving Burbank and the surrounding San Fernando Valley.